011 66487704
(9:00 AM to 9:00 PM)
case studies
0 204+
0h  0m
Time invested in
career planning

Msbte diploma sample question paper 2010-11 - 1 to 11 of 594 results

Dear Vishakha
You can check the following link for CATE sample papers

Best of luck for ur CATE Exam...
Qustion paper with answer for m.com 1st semester:
► Read more
No. Question paper printed in larger fonts is for visually impaired candidates and not for those who have normal vision with/without corrective eyewear.
► Read more
Sorry, you cant ask them for a question paper with a larger font size. The standard of question paper is same for everyone. There is no change in that. And even someone request for larger font paper they deny it. Now my point is, why you want to ask them for a larger font size paper.? It is perfectly ok, you can wear lenses/ spectacles during the examination. No one is going to ask you for this, that why are you wearing spectacles/lenses. So my advise is to carry your spectacles/lenses with you and wear them during examination.... ► Read more
The paper pattern of BITSAT 2012 is
BITSAT-2012 will be of total 3-hour duration (without break). The test consists of four parts:

Part I : Physics

Part II : Chemistry

Part III : (a) English Proficiency and (b) Logical Reasoning

Part IV : Mathematics

All questions are of objective type (multiple choice questions); each question with choice of four answers, only one being correct choice. Each correct answer fetches 3 marks, while each incorrect answer has a penalty of 1 mark (-1mark). No marks are awarded for questions not attempted. While the candidate can skip a question, the computer will not allow the candidate to choose more than one option as correct answer. There will be 150 questions in all. The number of questions in each part is as follows:


No of questions

Part I



Part II



Part III

(a) English Proficiency

(b) Logical Reasoning



Part IV





There is no time limit for individual parts of the test. The candidate can go back and change any of his/her answers among the 150 questions.

If a candidate answers all the 150 questions (without skipping any question), the candidate will have an option of attempting 12 (twelve) extra questions, if there is still time left. These extra questions will be from Physics, Chemistry, and Mathematics only; four questions from each part. Further, once the candidate has opted for extra questions, he cannot go back for correction of any of the earlier answered 150 questions.

The questions are so designed that a good student will be able to answer 150 questions in 180 minutes. The extra questions (a m
► Read more
The past four years CLAT question papers will be available at all the 14 National Law Universities on payment of Rs. 100/- (Rs. One Hundred Only). The question papers can also be obtained by post from National Law University, Jodhpur. Candidates must enclose a demand draft of Rs. 150/- (Rs. One Hundred Fifty Only) in favour of “National Law University, Jodhpur CLAT A/C” payable at Jodhpur (Rajasthan). Application requesting the question paper should be addressed to The Convenor, Common Law Admission Test, CLAT 2012, National Law University, Jodhpur, NH-65, Nagour Road, Mandore, Jodhpur - 342304 (Rajasthan). The application can be made on a plain piece of paper and should contain the following information - a) Name, b) Complete Postal Address including pincode, c) Contact Number(Landline and Mobile), and d) Email id.... ► Read more
Basically , It totally depend upon your interest. If you are intrested in maths and science then you should choose PCM stream and If you are intrested in accounts portion then you should choose commerce stream. After choosing PCM stream, you can do B.Tech , IIT. And after choosing Commerce stream, you can do CA, CS or ICWAI.... ► Read more
Most of the students face this problem at your age.... But there is nothing to panic.... There are a lot many career opportunities who opts for maths with bio..... Most commonly students opt for either engineering or medical field, but career is not so limited you can also pursue with animation, game designing, mass communication, law, hotel management, fashion designing, counselling, just B.Sc. and many such other. If you are interested in Army, Navy or Air Force you can even apply for National Defense Academy...... All the fields are equally good, you just need to choose one which suits you............
► Read more
Partha you can study any subject upto graduation and then take up MBA in your field of choice. Course in the field of economics, commerce, bachelor of business administration, finace, business economics will be good at graduation level. as by taking such course you will be learning concepts which can be useful at MBA level. But as suggested you can do any course as MBA is open to every one with eligibility of graduation.... ► Read more
The best way of dealing such situation is to talk to HR person and supporting seniors of your company for matter related with job profile A good discussion with HR and senior will help . Do tell them your problem but be polite in entire discussion .They can tell you ways of how to solve issue of job profile . Leave your job only if you have got some better job offer . There is no point sitting in home unemployed Also keep on searching for job simultaneously through newspapers, job portals like naukri.com , monster.com, , social networking site like LINKEDIN, APNA CIRCLE , recruitment consultants. You can also send your resume to company of this field when they have requirement they will inform you . Another way is trying for PG level qualification like MBA or M.TECH , it will give better career opportunities and better career growth. You had got year of experience so change in job profile is not difficult but moving towards management become more easy if you have degree to support that .

Some of the certification courses for a B.Tech in Mechanical Engineering graduate include the following.. These certification can help you improve your performance if you are lacking in some skill which can play critical role in increasing your salary .

Auto CAD
Piping – Stress Analysis
Computer Aided Manufacture
Tool Design
CNC Machining
First try for PG level qualification if possible...
► Read more

There is more to explore...

    Sign Up   
Already have an account? Login